Forum Replies Created
-
AuthorPosts
-
glcmrangerParticipant
I attempted to send you guys the schematic via email but it doesn’t recognize those email addresses.
glcmrangerParticipantHere’s the part # for the T Handles: 92-21-532, T- & L-Handle Style Cam Latches, Southco.
Just google to find a distributor. I can’t find the company I ordered through,,,,, Amazon has it listed but you get the “don’t know when this item is back in stock” message.
Good Luck!
glcmrangerParticipantGalley: I followed the above post idea… I have two (not one) locking handles on the galley lid.
Question: Has anyone figured out a hinge that is a hidden type for the side doors of the UCC?
glcmrangerParticipantFrom what I remember, I did not glass the galley flat — reason is it would be hard to install because it wouldn’t bend. However, I did use fiberglass tape on the filet seams,,, i also used tape under the inside shelf which is mentioned in the manual.
glcmrangerParticipantI would buy 5 quarts….. that’s based on 6 coats applied on the entire Teardrop. Extra could be used as touchup.
glcmrangerParticipantJohn: I just completed the drawers and now will be assembling the frame. I also was worried about the filets on those seams….. Thanks for sharing — I think I’ll make them very small BUT use plexiglass tape to provide the strength. Please let me know what other challenges you encounter with the ICC. Sorry I don’t have anything to share,,,, but, once you start on the Teardrop,,,,,, I’ll have a lot of suggestions for you. CHEERS!
glcmrangerParticipantI just sized it against the lid. However, I might add a strike plate later……. its very easy to adjust the CAM latch to accommodate the strike plate or add more pressure once the gasket starts to settle in.
glcmrangerParticipantYes. I installed 2 CAM Latches. Go back in this forum and search on “Dan’s Build” – maybe on page # 9 or 10? I followed his procedure – it worked brilliantly! I used this SOUTHCO Part: SOUTHCO T-Handle Style Cam Latch (92-21-532). Amazon doesn’t have them in stock right now,,,, so I googled another company. I LOVE these latches…. I hope this helps.
glcmrangerParticipantCall CLC. Mine have been back ordered since November……. probably yours too. Thule is coming out with a new design in March.
glcmrangerParticipantOne more thing. I have a plug-in Marinco port which is wired to the Minnoka On-Board Battery Charger.
glcmrangerParticipantWudboatVT: See attached Wiring Diagram. I run everything off a Battleborn Lithium ION battery. My components include:
– Refrigerator in Storage Box
– Radio/Speakers
– 60 Watt Solar Panel on Storage Box (Also have a portable Solar port)
– Television
– Reading lights and Puck Lights
– Both small fans and overhead Fantastic Fan
– Puck lights in Galley
– Voyager Backup Camera (tied into Trailer Trailer twilight)
–
glcmrangerParticipantrsbrownmd: I got my toilet bucket on Amazon — item is titled: Reliance Control Corporation Luggable Loo Portable 5 Gallon Toilet. I also decorated it in camoflage shelf liner to jazz it up a bit.
glcmrangerParticipantI won’t until I go on a trip to the Everglades in mid-February…. I’ll post then. I also bought a Toilet seat bucket for those middle of the night “gotta go” scenarios. Just put a liner in it with kitty litter.
glcmrangerParticipantFirst off, I installed the ARB awning to the Thule Roof Rack Load bars — Works great!
Then when I set up camp, I deploy my CLAM tent and put up the privacy screens on the street side…. that way, the tent is my changing room. I also have a dog — so I put up a pet fence so my dog can go in/out of the Teardrop and tent.
I hope this helps…
glcmrangerParticipantThen get an AGM battery which will only last 4 years and weigh 3 times more.
-
AuthorPosts